Search results for 'temperature sensor'
-
$16.50Replaces Ultimaker2 teflon part. This is made of PTFE but it's a high temperature teflon. First there was regular PTFE (both Ultimaker and 3dsolex). Then there was "TFT" (3dsolex and soon after Ultimaker). Now there is "TFN". TFN lasts about the same amount of time as TFT depending on temperature. Learn More
-
$18.90Insulator - for Ultimaker2 - goes between white teflon isolator and heater block (Olsson or Ultimaker). Learn More -
Regular Price: $10.90
Special Price $9.80
Slippery “ICE” nozzle, with brass core. Optimized for surface prints. Max temp 275C. First 2 hours max 220C to temper the nozzle. Super Easy Cold-Pulls! Has an outer geometry optimized for surfaces. This is a brass nozzle (excellent temperature properties) with a hard slippery “ICE” coating. This coating prevents hot plastic from sticking to it! If you heat it to more than 275C, it destroys this function and the nozzle acts like a “normal” nozzle. IMPORTANT: This ICE nozzle looks like a (dark) steel nozzle, but it is a brass nozzle! This means it prints just like a standard brass nozzles (several times faster than steel nozzles). Fits UM2, UM2+, Olsson Block, Matchless V3 Learn More -
Starting at: $9.80
It's not the one from Ultimaker. This is my version of their upgrade kit. Much less expensive - please read description below.Set qty to zero for what you already have or don't want and then "add to cart".
PLEASE READ FULL DESCRIPTION BELOW. Learn More
-
$40.00Wow - heated bed conversion kit for UM2GO! Includes everything you need: Peel-and-stick heater with temp sensor, firmware. Instructions and more details are here.This is version 2 of the kit which is cheaper, easier to install (version 1 required installing a new nozzle heater) and it smells better (I found the silicone version was a little stinky when printing ABS - although the ABS also smells bad). Learn More
-
Regular Price: $10.90
Special Price $9.80
Slippery “ICE” nozzle, with brass core. Optimized for surface prints. Max temp 275C. First 2 hours max 220C to temper the nozzle. Super Easy Cold-Pulls! Has an outer geometry optimized for surfaces. This is a brass nozzle (excellent temperature properties) with a hard slippery “ICE” coating. This coating prevents hot plastic from sticking to it! If you heat it to more than 275C, it destroys this function and the nozzle acts like a “normal” nozzle. IMPORTANT: This ICE nozzle looks like a (dark) steel nozzle, but it is a brass nozzle! This means it prints just like a standard brass nozzles (several times faster than steel nozzles). Fits UM2, UM2+, Olsson Block, Matchless V3 Learn More -
Regular Price: $10.90
Special Price $9.80
Slippery “ICE” nozzle, with brass core. Optimized for surface prints. Max temp 275C. First 2 hours max 220C to temper the nozzle. Super Easy Cold-Pulls!Has an outer geometry optimized for surfaces. This is a brass nozzle (excellent temperature properties) with a hard slippery “ICE” coating. This coating prevents hot plastic from sticking to it! If you heat it to more than 275C, it destroys this function and the nozzle acts like a “normal” nozzle.
IMPORTANT: This ICE nozzle looks like a (dark) steel nozzle, but it is a brass nozzle! This means it prints just like a standard brass nozzles (several times faster than steel nozzles). Fits UM2, UM2+, Olsson Block, Matchless V3 Learn More