Ultimaker 2 (3mm)
-
$4.002mm Hex wrench - fits over 90% of the screws on the UM printers (UMO, UM2, UM2+, etc). Ball end allows up to 20 degree angle when tightening or loosening screws. Learn More -
$40.00Wow - heated bed conversion kit for UM2GO! Includes everything you need: Peel-and-stick heater with temp sensor, firmware. Instructions and more details are here.This is version 2 of the kit which is cheaper, easier to install (version 1 required installing a new nozzle heater) and it smells better (I found the silicone version was a little stinky when printing ABS - although the ABS also smells bad). Learn More
-
$5.20Compatible with UM Original and UM2, UM2go, UM2ext bowden tubes and printers. Both ends. You get a pair. Learn More -
$18.90Much more resistant to breaking. Precisely engineered. If you lose the original on the floor, it may break or bend. When turning, it may break.The V2 is much stronger. Learn More -
$18.90Insulator - for Ultimaker2 - goes between white teflon isolator and heater block (Olsson or Ultimaker). Learn More -
$12.20 As low as: $12.000.5mm Steel nozzle! Meant for printing abrasive materials. Learn More -
$9.801mm nozzle for really fast prints. If you plan to do .5mm layer height it's recommended to also get a 35W or 40W heater.These nozzles are e3dv6 compatible meaning they work with all versions of the Olsson block including the one on the Ultimaker 2+. They work on other reprap printers also.
The JET RSB have a revised tip angle, revised jet shoulder width and revised internal geometry, with a gentle slope leading down to the exit. They are also slippery inside, due to a special treatment.
These new nozzles are meant for Speed! Plastic will flow more easily than in most other nozzles. Atomic pulls work very well! The inside geometry makes it much harder for plastic to “hide in the corners”, so changing color/filament type will be quicker and safer.
For "3mm" filament (not 1.75mm filament). Learn More
-
Regular Price: $10.90
Special Price $9.80
Slippery “ICE” nozzle, with brass core. Optimized for surface prints. Max temp 275C. First 2 hours max 220C to temper the nozzle. Super Easy Cold-Pulls! Has an outer geometry optimized for surfaces. This is a brass nozzle (excellent temperature properties) with a hard slippery “ICE” coating. This coating prevents hot plastic from sticking to it! If you heat it to more than 275C, it destroys this function and the nozzle acts like a “normal” nozzle. IMPORTANT: This ICE nozzle looks like a (dark) steel nozzle, but it is a brass nozzle! This means it prints just like a standard brass nozzles (several times faster than steel nozzles). Fits UM2, UM2+, Olsson Block, Matchless V3 Learn More -
$9.80.8mm JET RSB Nozzle. Compatible with e3d v6 nozzles designed for 3mm filament. Learn More -
Regular Price: $10.90
Special Price $9.80
Slippery “ICE” nozzle, with brass core. Optimized for surface prints. Max temp 275C. First 2 hours max 220C to temper the nozzle. Super Easy Cold-Pulls! Has an outer geometry optimized for surfaces. This is a brass nozzle (excellent temperature properties) with a hard slippery “ICE” coating. This coating prevents hot plastic from sticking to it! If you heat it to more than 275C, it destroys this function and the nozzle acts like a “normal” nozzle. IMPORTANT: This ICE nozzle looks like a (dark) steel nozzle, but it is a brass nozzle! This means it prints just like a standard brass nozzles (several times faster than steel nozzles). Fits UM2, UM2+, Olsson Block, Matchless V3 Learn More
You have no items to compare.
