Search results for 'JET Set 4'
-
$9.80 As low as: $9.00Click here for ICE version.4mm JET RSB Nozzle. Compatible with e3d v6 nozzles designed for 3mm filament. Learn More
-
$40.00ALL BATH INTERFEROMETER PRODUCTS HAVE BEEN MOVED TO MY NEW STORE HERE:
https://thegr5store.com/wp/All the parts you need to build a nice XYZ stage for a Bath Interferometer or other optical stage.
Missing:- tools including a metal file (see assembly instructions at bottom for tool list)
- interferometer
- 1/4 inch metal rods precut to fit
- brass tubing pieces to go around the 1/4 inch rods
- precut 8-32 threaded rods
- 4 8-32 nuts
- 6 8-32 lock nuts
- a long 8-32 screw for purposes of tapping the plastic parts
- two short M3 screws that will hold down equipment to the top of the XYZ table
-
$4.002mm Hex wrench - fits over 90% of the screws on the UM printers (UMO, UM2, UM2+, etc). Ball end allows up to 20 degree angle when tightening or loosening screws. Learn More -
$9.80.8mm JET RSB Nozzle. Compatible with e3d v6 nozzles designed for 3mm filament. Learn More -
$15.00ALL BATH INTERFEROMETER PRODUCTS HAVE BEEN MOVED TO MY NEW STORE HERE:
https://thegr5store.com/wp/The plastic parts you need to build a nice XYZ stage for an interferometer or Foucault test.
Missing:
2 feet of 1/4 inch stainless steel rod
1 foot of brass tubing to go around that
1 foot of 8-32 threaded rod
3 8-32 nuts
6 8-32 lock nuts
Interferometer Learn More -
$40.00Wow - heated bed conversion kit for UM2GO! Includes everything you need: Peel-and-stick heater with temp sensor, firmware. Instructions and more details are here.This is version 2 of the kit which is cheaper, easier to install (version 1 required installing a new nozzle heater) and it smells better (I found the silicone version was a little stinky when printing ABS - although the ABS also smells bad). Learn More
-
$10.00ALL BATH INTERFEROMETER PRODUCTS HAVE BEEN MOVED TO MY NEW STORE HERE:
https://thegr5store.com/wp/ This part is from surplus shed part number L13545 (or equivalent)I won't test your specific lens but I have tested a few of these and they are excellent. They will give you better than 1/50 wave accuracy when using for a Bath Interferometer.
Mount for lens is included. Lens will arrive mounted.
Too bright!Learn More
-
$195.00This needs to be paired with a 1.75mm hardcore - email us for details: thegr5store@gmail.comThis feeder expects a 1/4 inch (6.35mm) O.D. bowden tube - not the typical 4mm O.D. bowden tube for 1.75mm filament.
DDG Extruder for Ultimaker3 that feeds filament without grinding and with a very firm grip of the filament that will allow for faster printing without under-extrusion problems and also high retraction prints like Voroni models without grinding. Learn More
-
$29.00EXPERTS ONLY - 0.15mm JET RSB Nozzle. Compatible with e3d v6 nozzles designed for 3mm filament. Learn More -
Starting at: $10.00
ALL BATH INTERFEROMETER PRODUCTS HAVE BEEN MOVED TO MY NEW STORE HERE:
https://thegr5store.com/wp/ The interferometer will be assembled. The xyz stage can be bought as a kit which takes 1-3 hours to assemble or you can buy an assembled stage for another $50 for the labor (if in stock).Much more information in description section far below (scroll way down). Learn More