Search results for 'olson block no tools'
-
$35.00ALL BATH INTERFEROMETER PRODUCTS HAVE BEEN MOVED TO MY NEW STORE HERE:
https://thegr5store.com/wp/Learn More -
$9.801mm nozzle for really fast prints. If you plan to do .5mm layer height it's recommended to also get a 35W or 40W heater.These nozzles are e3dv6 compatible meaning they work with all versions of the Olsson block including the one on the Ultimaker 2+. They work on other reprap printers also.
The JET RSB have a revised tip angle, revised jet shoulder width and revised internal geometry, with a gentle slope leading down to the exit. They are also slippery inside, due to a special treatment.
These new nozzles are meant for Speed! Plastic will flow more easily than in most other nozzles. Atomic pulls work very well! The inside geometry makes it much harder for plastic to “hide in the corners”, so changing color/filament type will be quicker and safer.
For "3mm" filament (not 1.75mm filament). Learn More
-
$40.00ALL BATH INTERFEROMETER PRODUCTS HAVE BEEN MOVED TO MY NEW STORE HERE:
https://thegr5store.com/wp/All the parts you need to build a nice XYZ stage for a Bath Interferometer or other optical stage.
Missing:- tools including a metal file (see assembly instructions at bottom for tool list)
- interferometer
- 1/4 inch metal rods precut to fit
- brass tubing pieces to go around the 1/4 inch rods
- precut 8-32 threaded rods
- 4 8-32 nuts
- 6 8-32 lock nuts
- a long 8-32 screw for purposes of tapping the plastic parts
- two short M3 screws that will hold down equipment to the top of the XYZ table
-
$18.90Replaces Ultimaker Original (not Ultimaker2) teflon part but this part can print at 255C continuous for years. Never replace your teflon part again. This is made of teflon but it's a high temperature teflon. Learn More -
$75.00 -
$12.20 As low as: $12.000.5mm Steel nozzle! Meant for printing abrasive materials. Learn More -
$285.00100% 3DSolex parts. Compatible with Ultimaker 3, S3 and S5 PrintersYou get a complete core already upgraded to include the 3DSolex hardcore heater block which lets you change nozzles. Included nozzles:
- .25mm
- .40mm (race) X 2
- .50mm steel
- .60mm (race)
- .80mm (race)
- 1.0mm (race)
-
$15.00ALL BATH INTERFEROMETER PRODUCTS HAVE BEEN MOVED TO MY NEW STORE HERE:
https://thegr5store.com/wp/The plastic parts you need to build a nice XYZ stage for an interferometer or Foucault test.
Missing:
2 feet of 1/4 inch stainless steel rod
1 foot of brass tubing to go around that
1 foot of 8-32 threaded rod
3 8-32 nuts
6 8-32 lock nuts
Interferometer Learn More -
$4.002mm Hex wrench - fits over 90% of the screws on the UM printers (UMO, UM2, UM2+, etc). Ball end allows up to 20 degree angle when tightening or loosening screws. Learn More -
$68.00For Prusa I3 Mk3.
3DSolex is out of silicone socks so if you don't have any there are plenty of other ways to get those.
This sensational kit for the Prusa I3 Mk3 will transform your printer.
Safely change nozzle using our tools included in kit.
Ramp up plastic output thanks to our patented core heating nozzles and fully utilizing the Bondtech feeder already installed in your printer. By combining nozzle size, layer height and speed you can achieve up to 30 cubics / second.
Learn More